Udkik.dk

Review of Trintella II A


Basic specs.

sail specifications
The Trintella II A is a sailboat designed by the Dutch maritime architect E. G. van de Stadt. The Trintella II A is built by the Dutch yard Wever B.V., Anne, Jachtwerf.

Here we would have liked to show you nice photos of the Trintella II A.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Trintella II A or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Rig
The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Engine

The boat is typically equipped with an inboard Volvo Penta diesel engine.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Trintella II A is about 195 kg/cm, alternatively 1093 lbs/inch.
Meaning: if you load 195 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1093 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Trintella II A is 3.61.

Wide Slim 85% 0 50 100
Compared with other similar sailboats it is slimmer than 85% of all other designs. It seems that the designer has chosen a significantly more speedy hull design.


Maintenance

Rig

Dimensions of sail for masthead rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 29.2 m(95.7 feet)10 mm(3/8 inch)
Jib/genoa halyard29.2 m(95.7 feet)10 mm(3/8 inch)
Spinnaker halyard29.2 m(95.7 feet)10 mm(3/8 inch)
Jib sheet 10.3 m(33.7 feet)12 mm(1/2 inch)
Genoa sheet10.3 m(33.7 feet)12 mm(1/2 inch)
Mainsheet 25.6 m(84.2 feet)12 mm(1/2 inch)
Spinnaker sheet22.6 m(74.1 feet)12 mm(1/2 inch)
Cunningham3.7 m(12.1 feet)10 mm(3/8 inch)
Kickingstrap7.4 m(24.3 feet)10 mm(3/8 inch)
Clew-outhaul7.4 m(24.3 feet)10 mm(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Trintella II A it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References