Udkik.dk

Review of Tartan 48


Basic specs.

sail specifications
The Tartan 48 is a large sailboat designed by the American maritime architect bureau Sparkman & Stephens in the early seventies. Only a few boats have been produced. The Tartan 48 is built by the American yard Tartan Marine.

Here we would have liked to show you nice photos of the Tartan 48.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Tartan 48 or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Rig
The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The Tartan 48 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can only enter major marinas as the draft is about 2.31 - 2.41 meter (7.58 - 7.88 ft) dependent on the load. See immersion rate below.


Engine

The boat is typically equipped with an inboard Perkins diesel engine.

The fuel tank has a capacity of 288.0 liters (76 US gallons, 63 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Tartan 48 is 1.83, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Tartan 48 is about 313 kg/cm, alternatively 1757 lbs/inch.
Meaning: if you load 313 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1757 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Tartan 48 is 32.8.

Low High 46% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 46% of all similar sailboat designs. This comfort value is just below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Tartan 48 is 3.43.

Slim Wide 54% 0 50 100
Compared with other similar sailboats it is more spacy than 54% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Tartan 48 is 272 which categorizes this boat among 'light crusers & offshore racers'.

Heavy Light 34% 0 50 100
34% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Tartan 48 with ISO 8666 reference sail is 18.1, with a 135% genua the SA/D is 21.6.

Low High 34% 0 50 100
The SA/D ratio indicates that it is faster than 34% of all similar sailboat designs in light wind.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 54m2 (581 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for masthead rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 42.1 m(138.0 feet)14 mm(0.55 inch)
Jib/genoa halyard42.1 m(138.0 feet)14 mm(0.55 inch)
Spinnaker halyard42.1 m(138.0 feet)14 mm(0.55 inch)
Jib sheet 14.6 m(48.0 feet)16 mm(5/8 inch)
Genoa sheet14.6 m(48.0 feet)16 mm(5/8 inch)
Mainsheet 36.6 m(120.0 feet)16 mm(5/8 inch)
Spinnaker sheet32.2 m(105.6 feet)16 mm(5/8 inch)
Cunningham5.3 m(17.5 feet)14 mm(0.55 inch)
Kickingstrap10.7 m(35.0 feet)14 mm(0.55 inch)
Clew-outhaul10.7 m(35.0 feet)14 mm(0.55 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Tartan 48 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References