Udkik.dk

Review of Swan CS42


Basic specs.

sail specifications
The Swan CS42 is a large sailboat designed by the Argentine maritime architect Germán Frers in the mid 2000. The Swan CS42 is built by the Finnish yard Oy Nautor AB.

Here we would have liked to show you nice photos of the Swan CS42.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Swan CS42 or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Rig
The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can only enter major marinas as the draft is about 2.70 - 2.80 meter (8.86 - 9.16 ft) dependent on the load. See immersion rate below.


Engine

The boat is typically equipped with an inboard Volvo Penta diesel engine at 40.0 hp (29 kW), which gives a max speed about 7.2 knots.

The fuel tank has a capacity of 148.0 liters (39 US gallons, 32 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Swan CS42 is 2.05, indicating that this boat would not be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Swan CS42 is about 297 kg/cm, alternatively 1664 lbs/inch.
Meaning: if you load 297 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1664 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Swan CS42 is 21.0.

Low High 10% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 10% of all similar sailboat designs. This is a comfort value significantly below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Swan CS42 is 3.30.

Slim Wide 54% 0 50 100
Compared with other similar sailboats it is more spacy than 54% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Swan CS42 is 44%.

Low High 79% 0 50 100
This ballast ratio shows a righting moment that is higher than 79% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly above average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Swan CS42 is 140 which categorizes this boat among 'ultra light racers'.

Heavy Light 90% 0 50 100
90% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Swan CS42 with ISO 8666 reference sail is 25.7, with a 135% genua the SA/D is 29.9.

Low High 100% 0 50 100
The SA/D ratio indicates that it is faster than 100% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 62% 0 50 100
The Swan CS42 has more rig than 62% of all similar sailboats, which indicates that the boat is slightly overrigged.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 56m2 (602 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for fractional rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 44.4 m(145.7 feet)12 mm(1/2 inch)
Jib/genoa halyard44.4 m(145.7 feet)12 mm(1/2 inch)
Spinnaker halyard44.4 m(145.7 feet)12 mm(1/2 inch)
Jib sheet 13.0 m(42.6 feet)14 mm(0.55 inch)
Genoa sheet13.0 m(42.6 feet)14 mm(0.55 inch)
Mainsheet 32.5 m(106.5 feet)14 mm(0.55 inch)
Spinnaker sheet28.6 m(93.7 feet)14 mm(0.55 inch)
Cunningham5.8 m(19.0 feet)12 mm(1/2 inch)
Kickingstrap11.6 m(37.9 feet)12 mm(1/2 inch)
Clew-outhaul11.6 m(37.9 feet)12 mm(1/2 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Swan CS42 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References