Review of Swan 57 RS

Basic specs.

The Swan 57 RS is a sailboat designed by the Argentine maritime architect Germán Frers in the mid nineties. Only a few boats have been produced. The Swan 57 RS is built by the Finnish yard OY Nautor AB.

Here we would have liked to show you nice photos of the Swan 57 RS.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Swan 57 RS or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Rig

The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The Swan 57 RS is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can only enter major marinas as the draft is about 2.30 - 2.40 meter (7.55 - 7.85 ft) dependent on the load. See immersion rate below.

Engine

The boat is typically equipped with an inboard Perkins Sabre M135 diesel engine at 125.0 hp (93 kW), which gives a max speed about 7.5 knots.

The fuel tank has a capacity of 1050.0 liters (277 US gallons, 230 imperial gallons).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Swan 57 RS is 1.68, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.9 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Swan 57 RS is about 439 kg/cm, alternatively 2459 lbs/inch.
Meaning: if you load 439 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 2459 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Swan 57 RS is 3.62.

Compared with other similar sailboats it is more spacy than 50% of all other designs. It seems that the designer has chosen an average hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Swan 57 RS is 38%.

This ballast ratio shows a righting moment that is higher than 66% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Swan 57 RS is 273 which categorizes this boat among 'light crusers & offshore racers'.

21% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Swan 57 RS with ISO 8666 reference sail is 15.1, with a 135% genua the SA/D is 17.9.

The SA/D ratio indicates that it is faster than 8% of all similar sailboat designs in light wind.

Over- / underrigged

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 73m² (785 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail for masthead rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	47.9 m	(157.3 feet)	14 mm	(0.55 inch)
Jib/genoa halyard	47.9 m	(157.3 feet)	14 mm	(0.55 inch)
Spinnaker halyard	47.9 m	(157.3 feet)	14 mm	(0.55 inch)
Jib sheet	17.5 m	(57.4 feet)	16 mm	(5/8 inch)
Genoa sheet	17.5 m	(57.4 feet)	16 mm	(5/8 inch)
Mainsheet	43.7 m	(143.5 feet)	16 mm	(5/8 inch)
Spinnaker sheet	38.5 m	(126.2 feet)	16 mm	(5/8 inch)
Cunningham	6.3 m	(20.7 feet)	14 mm	(0.55 inch)
Kickingstrap	12.6 m	(41.3 feet)	14 mm	(0.55 inch)
Clew-outhaul	12.6 m	(41.3 feet)	14 mm	(0.55 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Swan 57 RS it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.