Udkik.dk

Review of Sparrow 16


Basic specs.

sail specifications
The Sparrow 16 is a small sailboat designed by the maritime architect Ron Holder in the early eighties. A few hundred boats have been produced. The Sparrow 16 is built by the American yard Northshore Marine.

Here we would have liked to show you nice photos of the Sparrow 16.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Sparrow 16 or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Rig
The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

The Sparrow 16 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can enter even shallow marinas as the draft is just about 0.56 - 0.66 meter (1.84 - 2.14 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Sparrow 16 is 2.69, indicating that this boat would not be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 5.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Sparrow 16 is about 58 kg/cm, alternatively 328 lbs/inch.
Meaning: if you load 58 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 328 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Sparrow 16 is 7.6.

Low High 38% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 38% of all similar sailboat designs. This comfort value is just below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Sparrow 16 is 2.52.

Slim Wide 62% 0 50 100
Compared with other similar sailboats it is more spacy than 62% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Sparrow 16 is 131 which categorizes this boat among 'ultra light racers'.

Heavy Light 66% 0 50 100
66% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Sparrow 16 with ISO 8666 reference sail is 18.8, with a 135% genua the SA/D is 21.3.

Low High 76% 0 50 100
The SA/D ratio indicates that it is faster than 76% of all similar sailboat designs in light wind.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 8m2 (86 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for fractional rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 14.6 m(47.8 feet)6 mm(1/4 inch)
Jib/genoa halyard14.6 m(47.8 feet)6 mm(1/4 inch)
Spinnaker halyard14.6 m(47.8 feet)6 mm(1/4 inch)
Jib sheet 5.0 m(16.3 feet)8 mm(5/16 inch)
Genoa sheet5.0 m(16.3 feet)8 mm(5/16 inch)
Mainsheet 12.5 m(40.8 feet)8 mm(5/16 inch)
Spinnaker sheet11.0 m(35.9 feet)8 mm(5/16 inch)
Cunningham2.4 m(7.7 feet)6 mm(1/4 inch)
Kickingstrap4.7 m(15.5 feet)6 mm(1/4 inch)
Clew-outhaul4.7 m(15.5 feet)6 mm(1/4 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Sparrow 16 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References