Udkik.dk

Review of Spækhugger


Spækhugger
Spækhugger anno 1977.


Basic specs.

sail specifications
The Spækhugger aka Spaekhugger is a sailboat designed by the Danish maritime architect Peter Bruun in the late sixties. Several hundred boats have been produced. The Spækhugger is built by the Danish yard P. Bjørn Olsens Bådeværft ApS.

Looking for a new boat? Find a Spækhugger or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Interior
Interior
Interior of Spækhugger anno 1977. Spækhugger Family
The boat is equipped with one cabin and 4 berths.

Rig
The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel
Keel
Keel of Spækhugger.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated.

The boat can enter even shallow marinas as the draft is just about 1.45 - 1.55 meter (4.76 - 5.06 ft) dependent on the load. See immersion rate below.


Engine

An outboard motor is often used on this boat. In that case Spækhugger will typically require a power of 5 - 6 hp, alternatively 102 - 122 lbs thrust if you prefer an electrical motor. Electric outboards are becoming popular for sailboat owners who want clean instant power with less noise and no exhaust fumes.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Spækhugger is 1.78, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Spækhugger is about 98 kg/cm, alternatively 551 lbs/inch.
Meaning: if you load 98 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 551 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Spækhugger is 23.8.

Low High 88% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 88% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Spækhugger is 3.19.

Wide Slim 79% 0 50 100
Compared with other similar sailboats it is slimmer than 79% of all other designs. It seems that the designer has chosen a significantly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Spækhugger is 59%.

Low High 99% 0 50 100
This ballast ratio shows a righting moment that is higher than 99% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly above average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Spækhugger is 255 which categorizes this boat among 'light crusers & offshore racers'.

Heavy Light 34% 0 50 100
34% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Spækhugger with ISO 8666 reference sail is 16.9, with a 135% genua the SA/D is 19.7.

Low High 50% 0 50 100
The SA/D ratio indicates that it is faster than 50% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 15% 0 50 100
The Spækhugger has more rig than 15% of all similar sailboats, which indicates that the boat is significantly underrigged.


RSP (Relative Speed Performance)

What is Relative Speed Performance?

The Relative Speed Performance for Spækhugger is 76

Slow Fast 76% 0 50 100
The relative speed performance is 76 which means that a it is faster than 76% of all similar sailboat designs.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 18m2 (193 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for fractional rig.

mainsail specifications genoa specifications spinnaker specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 25.3 m(83.0 feet)8 mm(5/16 inch)
Jib/genoa halyard25.3 m(83.0 feet)8 mm(5/16 inch)
Spinnaker halyard25.3 m(83.0 feet)8 mm(5/16 inch)
Jib sheet 7.4 m(24.4 feet)10 mm(3/8 inch)
Genoa sheet7.4 m(24.4 feet)10 mm(3/8 inch)
Mainsheet 18.6 m(61.0 feet)10 mm(3/8 inch)
Spinnaker sheet16.4 m(53.7 feet)10 mm(3/8 inch)
Cunningham3.2 m(10.5 feet)8 mm(5/16 inch)
Kickingstrap6.4 m(21.0 feet)8 mm(5/16 inch)
Clew-outhaul6.4 m(21.0 feet)8 mm(5/16 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Spækhugger it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References