Udkik.dk

Review of Sagitta 35


Sagitta 35
Sagitta 35 anno 1975. Kattegat i let vind med S35 Lise


Basic specs.

sail specifications
The Sagitta 35 is a sailboat designed by the American maritime architect bureau Sparkman & Stephens in the late sixties. The Sagitta 35 is built by Sagitta.

Looking for a new boat? Find a Sagitta 35 or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Interior
The interior is like most other boats made of teak.
The boat is equipped with a galley and toilet facility.

Rig
Rig
Rig of Sagitta 35 anno 1976. Sagitta D-317, ´Senja´ i Lundeborg Havn sommeren 2006.
The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The Sagitta 35 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated. As the surface of a fin type keel is just a fraction of the total wet surface, the difference between an iron keel and a lead keel can in reality be ignored for cruising yachts.

The boat can only enter major marinas as the draft is about 1.83 - 1.93 meter (6.00 - 6.30 ft) dependent on the load. See immersion rate below.


Engine

Sagitta 35 is typically equipped with an inboard Volvo Penta MD2 diesel engine at 16.0 hp (11 kW), which gives a max speed about 4.0 knots.

The fuel tank has a capacity of 80.0 liters (21 US gallons, 17 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Sagitta 35 is 1.68, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.8 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Sagitta 35 is about 160 kg/cm, alternatively 901 lbs/inch.
Meaning: if you load 160 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 901 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Sagitta 35 is 34.9.

Low High 90% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 90% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Sagitta 35 is 3.39.

Wide Slim 69% 0 50 100
Compared with other similar sailboats it is slimmer than 69% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Sagitta 35 is 41%.

Low High 54% 0 50 100
This ballast ratio shows a righting moment that is higher than 54% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Sagitta 35 is 372 which categorizes this boat among 'heavy cruisers'.

Heavy Light 8% 0 50 100
8% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Sagitta 35 with ISO 8666 reference sail is 14.0, with a 135% genua the SA/D is 16.8.

Low High 15% 0 50 100
The SA/D ratio indicates that it is faster than 15% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 27% 0 50 100
The Sagitta 35 has more rig than 27% of all similar sailboats, which indicates that the boat is slightly underrigged.


RSP (Relative Speed Performance)

What is Relative Speed Performance?

The Relative Speed Performance for Sagitta 35 is 38

Slow Fast 38% 0 50 100
The relative speed performance is 38 which means that a it is faster than 38% of all similar sailboat designs.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 29m2 (312 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for masthead rig.

mainsail specifications genoa specifications spinnaker specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 31.1 m(101.9 feet)10 mm(3/8 inch)
Jib/genoa halyard31.1 m(101.9 feet)10 mm(3/8 inch)
Spinnaker halyard31.1 m(101.9 feet)10 mm(3/8 inch)
Jib sheet 10.4 m(34.3 feet)12 mm(1/2 inch)
Genoa sheet10.4 m(34.3 feet)12 mm(1/2 inch)
Mainsheet 26.1 m(85.7 feet)12 mm(1/2 inch)
Spinnaker sheet23.0 m(75.4 feet)12 mm(1/2 inch)
Cunningham3.4 m(11.0 feet)10 mm(3/8 inch)
Kickingstrap6.7 m(22.0 feet)10 mm(3/8 inch)
Clew-outhaul6.7 m(22.0 feet)10 mm(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Sagitta 35 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References