Review of Sadler 32

Basic specs.

The Sadler 32 is a sailboat designed by the maritime architect Sadler Bros. The Sadler 32 is built by the British yard Sadler Yachts.

Here we would have liked to show you nice photos of the Sadler 32.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Sadler 32 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Rig

The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The Sadler 32 is equipped with a long keel. A long keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.

The boat can enter most marinas as the draft is just about 1.68 - 1.78 meter (5.51 - 5.81 ft) dependent on the load. See immersion rate below.

Engine

The boat is typically equipped with an inboard Bukh 20 diesel engine at 20.0 hp (14 kW).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Sadler 32 is about 202 kg/cm, alternatively 1133 lbs/inch.
Meaning: if you load 202 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1133 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Sadler 32 is 2.97.

Compared with other similar sailboats it is more spacy than 69% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Sadler 32 is 44%.

This ballast ratio shows a righting moment that is higher than 66% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.

Over- / underrigged

The Sadler 32 has more rig than 31% of all similar sailboats, which indicates that the boat is slightly underrigged.

Maintenance

Rig

Dimensions of sail for masthead rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	28.7 m	(94.2 feet)	10 mm	(3/8 inch)
Jib/genoa halyard	28.7 m	(94.2 feet)	10 mm	(3/8 inch)
Spinnaker halyard	28.7 m	(94.2 feet)	10 mm	(3/8 inch)
Jib sheet	9.5 m	(31.1 feet)	12 mm	(1/2 inch)
Genoa sheet	9.5 m	(31.1 feet)	12 mm	(1/2 inch)
Mainsheet	23.7 m	(77.7 feet)	12 mm	(1/2 inch)
Spinnaker sheet	20.8 m	(68.4 feet)	12 mm	(1/2 inch)
Cunningham	3.2 m	(10.5 feet)	10 mm	(3/8 inch)
Kickingstrap	6.4 m	(21.0 feet)	10 mm	(3/8 inch)
Clew-outhaul	6.4 m	(21.0 feet)	10 mm	(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Sadler 32 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.