Review of Pacific 30

Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

The interior is like most other boats made of teak.
The boat is equipped with 3 berths, a galley and toilet facility.
Note: the boat has also been sold to be self-made/-interiored, which means that the quality of each boat may vary.

The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

The Pacific 30 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

Pacific 30 can enter even shallow marinas as the draft is just about 1.46 - 1.56 meter (4.79 - 5.09 ft) dependent on the load. See immersion rate below.

An outboard motor is often used on this boat. In that case the boat will typically require a power of 8 - 10 hp, alternatively 187 - 224 lbs thrust if you prefer an electrical motor. Electric outboards are becoming popular for sailboat owners who want clean instant power with less noise and no exhaust fumes.

The fuel tank has a capacity of 114.0 liters (30 US gallons, 25 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Pacific 30 is 1.68, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.6 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Pacific 30 is about 131 kg/cm, alternatively 738 lbs/inch.
Meaning: if you load 131 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 738 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Pacific 30 is 30.4.

Comparing this ratio with similar sailboats show that it is more comfortable than 86% of all similar sailboat designs. This is a comfort value significantly above average.

What is L/B (Length Beam Ratio)?

The l/b ratio for Pacific 30 is 3.40.

Compared with other similar sailboats it is slimmer than 79% of all other designs. It seems that the designer has chosen a significantly more speedy hull design.

What is a Ballast Ratio?

The ballast ratio for Pacific 30 is 43%.

This ballast ratio shows a righting moment that is higher than 62% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.

What is Displacement Length Ratio?

The DL-ratio for Pacific 30 is 299 which categorizes this boat among 'medium weight cruisers'.

31% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Pacific 30 with ISO 8666 reference sail is 11.7, with a 135% genua the SA/D is 13.6.

The SA/D ratio indicates that it is faster than 8% of all similar sailboat designs in light wind.

The Pacific 30 has more rig than 21% of all similar sailboats, which indicates that the boat is significantly underrigged.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 23m² (247 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Dimensions of sail for masthead rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

We are always looking for new photos. If you can contribute with photos for Pacific 30 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.