Udkik.dk

Review of Kelt 760


Basic specs.

sail specifications
The Kelt 760 is a small sailboat designed by the French maritime architect Jean Berret in the early eighties. The Kelt 760 is built by the French yard Kelt Marine Inc..

Here we would have liked to show you nice photos of the Kelt 760.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Kelt 760 or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Rig
The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The Kelt 760 has been built with more than one type of keel.

One option is a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated. As the surface of a fin type keel is just a fraction of the total wet surface, the difference between an iron keel and a lead keel can in reality be ignored for cruising yachts.

The boat can enter even shallow marinas as the draft is just about 0.75 - 0.85 meter (2.46 - 2.76 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Kelt 760 is about 123 kg/cm, alternatively 691 lbs/inch.
Meaning: if you load 123 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 691 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Kelt 760 is 2.64.

Slim Wide 86% 0 50 100
Compared with other similar sailboats it is more spacy than 86% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Kelt 760 is 44%.

Low High 69% 0 50 100
This ballast ratio shows a righting moment that is higher than 69% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.


Over- / underrigged

Low High 34% 0 50 100
The Kelt 760 has more rig than 34% of all similar sailboats, which indicates that the boat is slightly underrigged.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 22m2 (236 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for masthead rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 20.9 m(68.6 feet)8 mm(5/16 inch)
Jib/genoa halyard20.9 m(68.6 feet)8 mm(5/16 inch)
Spinnaker halyard20.9 m(68.6 feet)8 mm(5/16 inch)
Jib sheet 7.6 m(24.9 feet)10 mm(3/8 inch)
Genoa sheet7.6 m(24.9 feet)10 mm(3/8 inch)
Mainsheet 19.0 m(62.3 feet)10 mm(3/8 inch)
Spinnaker sheet16.7 m(54.9 feet)10 mm(3/8 inch)
Cunningham2.8 m(9.2 feet)8 mm(5/16 inch)
Kickingstrap5.6 m(18.4 feet)8 mm(5/16 inch)
Clew-outhaul5.6 m(18.4 feet)8 mm(5/16 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Kelt 760 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References