Udkik.dk

Review of Irwin 10/4


Basic specs.

sail specifications
The Irwin 10/4 is a small sailboat designed by the maritime architect Ted Irwin in the mid seventies. The Irwin 10/4 is built by the American yard Irwin Yacht & Marine Corp..

Here we would have liked to show you nice photos of the Irwin 10/4.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Irwin 10/4 or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Keel

The Irwin 10/4 is equipped with a centerboard keel. A centerboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

The boat can enter even shallow marinas as the draft is just about 0.84 - 0.94 meter (2.76 - 3.06 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Irwin 10/4 is 2.16, indicating that this boat would not be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Irwin 10/4 is about 140 kg/cm, alternatively 785 lbs/inch.
Meaning: if you load 140 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 785 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Irwin 10/4 is 20.9.

Low High 66% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 66% of all similar sailboat designs. This comfort value is just above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Irwin 10/4 is 2.45.

Slim Wide 96% 0 50 100
Compared with other similar sailboats it is more spacy than 96% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Irwin 10/4 is 29%.

Low High 12% 0 50 100
This ballast ratio shows a righting moment that is higher than 12% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Irwin 10/4 is 300 which categorizes this boat among 'medium weight cruisers'.

Heavy Light 21% 0 50 100
21% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Irwin 10/4 with ISO 8666 reference sail is 17.3, with a 135% genua the SA/D is 20.5.

Low High 58% 0 50 100
The SA/D ratio indicates that it is faster than 58% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 54% 0 50 100
The Irwin 10/4 has more rig than 54% of all similar sailboats, which indicates that the boat is slightly overrigged.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 26m2 (279 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 24.3 m(79.6 feet)8 mm(5/16 inch)
Jib/genoa halyard24.3 m(79.6 feet)8 mm(5/16 inch)
Spinnaker halyard24.3 m(79.6 feet)8 mm(5/16 inch)
Jib sheet 7.7 m(25.3 feet)10 mm(3/8 inch)
Genoa sheet7.7 m(25.3 feet)10 mm(3/8 inch)
Mainsheet 19.3 m(63.3 feet)10 mm(3/8 inch)
Spinnaker sheet17.0 m(55.7 feet)10 mm(3/8 inch)
Cunningham3.7 m(12.2 feet)8 mm(5/16 inch)
Kickingstrap7.5 m(24.5 feet)8 mm(5/16 inch)
Clew-outhaul7.5 m(24.5 feet)8 mm(5/16 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Irwin 10/4 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References