Review of Hunter 240

Hunter 240.

Basic specs.

The Hunter 240 is a small sailboat designed by the American maritime architect Hunter together with Luhrs also from United States of America. The Hunter 240 is built by the American yard Hunter Marine.

Looking for a new boat? Find a Hunter 240 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Interior

Floor plan of Hunter 240.

Interior of Hunter 240.

The interior is like most other boats made of teak.
The boat is equipped with 3 cabins, 5 berths, a galley, toilet facility and 10.0 liter waste water capacity.

Rig

Rig of Hunter 240.

The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

The boat can enter even shallow marinas as the draft is just about 0.46 - 0.56 meter (1.51 - 1.81 ft) dependent on the load. See immersion rate below.

Engine

An outboard motor is often used on this boat. In that case Hunter 240 will typically require a power of 2 - 3 hp, alternatively 46 - 55 lbs thrust if you prefer an electrical motor. Electric outboards are becoming popular for sailboat owners who want clean instant power with less noise and no exhaust fumes.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Hunter 240 is 2.49, indicating that this boat would not be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Hunter 240 is about 113 kg/cm, alternatively 633 lbs/inch.
Meaning: if you load 113 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 633 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Hunter 240 is 9.4.

Comparing this ratio with similar sailboats show that it is more comfortable than 10% of all similar sailboat designs. This is a comfort value significantly below average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Hunter 240 is 2.92.

Compared with other similar sailboats it is more spacy than 54% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Hunter 240 is 57%.

This ballast ratio shows a righting moment that is higher than 98% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly above average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Hunter 240 is 95 which categorizes this boat among 'ultra light racers'.

93% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Hunter 240 with ISO 8666 reference sail is 22.2, with a 135% genua the SA/D is 25.6.

The SA/D ratio indicates that it is faster than 88% of all similar sailboat designs in light wind.

Over- / underrigged

The Hunter 240 has more rig than 50% of all similar sailboats, which indicates that this rig is spot on average!

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 21m² (226 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail for fractional rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	19.8 m	(64.9 feet)	8 mm	(5/16 inch)
Jib/genoa halyard	19.8 m	(64.9 feet)	8 mm	(5/16 inch)
Spinnaker halyard	19.8 m	(64.9 feet)	8 mm	(5/16 inch)
Jib sheet	7.3 m	(24.1 feet)	10 mm	(3/8 inch)
Genoa sheet	7.3 m	(24.1 feet)	10 mm	(3/8 inch)
Mainsheet	18.4 m	(60.2 feet)	10 mm	(3/8 inch)
Spinnaker sheet	16.1 m	(53.0 feet)	10 mm	(3/8 inch)
Cunningham	3.4 m	(11.0 feet)	8 mm	(5/16 inch)
Kickingstrap	6.7 m	(22.0 feet)	8 mm	(5/16 inch)
Clew-outhaul	6.7 m	(22.0 feet)	8 mm	(5/16 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Hunter 240 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.