Review of Frers 41

Basic specs.

The Frers 41 is a large sailboat designed by the Argentine maritime architect Germán Frers. The Frers 41 is built by the American yard Carroll Marine Ltd..

Here we would have liked to show you nice photos of the Frers 41.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Frers 41 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Keel

The Frers 41 has been built with more than one type of keel.

One option is a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a long keel.But be aware that even though a Wing Keel keel is very good for speed racing, a fishing nets and the like in the water can easily make you into a troublesome situation.

The boat can enter most marinas as the draft is just about 1.70 - 1.80 meter (5.58 - 5.88 ft) dependent on the load. See immersion rate below.

Engine

The boat is typically equipped with an inboard Yanmar diesel engine at 35.0 hp (26 kW).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Frers 41 is about 329 kg/cm, alternatively 1846 lbs/inch.
Meaning: if you load 329 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1846 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Frers 41 is 3.06.

Compared with other similar sailboats it is more spacy than 76% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Frers 41 is 41%.

This ballast ratio shows a righting moment that is higher than 58% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.

Over- / underrigged

The Frers 41 has more rig than 93% of all similar sailboats, which indicates that the boat is significantly overrigged.

Maintenance

Rig

Dimensions of sail.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	37.3 m	(122.3 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	37.3 m	(122.3 feet)	12 mm	(1/2 inch)
Spinnaker halyard	37.3 m	(122.3 feet)	12 mm	(1/2 inch)
Jib sheet	12.3 m	(40.3 feet)	14 mm	(0.55 inch)
Genoa sheet	12.3 m	(40.3 feet)	14 mm	(0.55 inch)
Mainsheet	30.7 m	(100.6 feet)	14 mm	(0.55 inch)
Spinnaker sheet	27.0 m	(88.6 feet)	14 mm	(0.55 inch)
Cunningham	4.5 m	(14.7 feet)	12 mm	(1/2 inch)
Kickingstrap	9.0 m	(29.4 feet)	12 mm	(1/2 inch)
Clew-outhaul	9.0 m	(29.4 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Frers 41 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.