Review of First 21.7

Basic specs.

The First 21.7 is a small sailboat designed by the French maritime architect bureau Groupe Finot in the mid 2000.

Here we would have liked to show you nice photos of the First 21.7.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a First 21.7 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Rig

The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

The boat can enter even shallow marinas as the draft is just about 1.15 - 1.25 meter (3.77 - 4.07 ft) dependent on the load. See immersion rate below.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for First 21.7 is about 103 kg/cm, alternatively 581 lbs/inch.
Meaning: if you load 103 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 581 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for First 21.7 is 2.52.

Compared with other similar sailboats it is more spacy than 76% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.

Maintenance

Rig

Dimensions of sail for fractional rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	22.1 m	(72.3 feet)	8 mm	(5/16 inch)
Jib/genoa halyard	22.1 m	(72.3 feet)	8 mm	(5/16 inch)
Spinnaker halyard	22.1 m	(72.3 feet)	8 mm	(5/16 inch)
Jib sheet	6.2 m	(20.5 feet)	10 mm	(3/8 inch)
Genoa sheet	6.2 m	(20.5 feet)	10 mm	(3/8 inch)
Mainsheet	15.6 m	(51.3 feet)	10 mm	(3/8 inch)
Spinnaker sheet	13.8 m	(45.1 feet)	10 mm	(3/8 inch)
Cunningham	2.9 m	(9.4 feet)	8 mm	(5/16 inch)
Kickingstrap	5.7 m	(18.7 feet)	8 mm	(5/16 inch)
Clew-outhaul	5.7 m	(18.7 feet)	8 mm	(5/16 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for First 21.7 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.