Review of Cruisaire 36

Basic specs.

The Cruisaire 36 is a sailboat designed by the maritime architect Jules Fleder in the late sixties. Only a few boats have been produced. The Cruisaire 36 is built by the Chinese yard Cheoy Lee Shipyard Ltd..

Here we would have liked to show you nice photos of the Cruisaire 36.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Cruisaire 36 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Rig

The boat equipped with a ketch rig.

Keel

The Cruisaire 36 is equipped with a long keel. A long keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated.

The boat can enter most marinas as the draft is just about 1.55 - 1.65 meter (5.09 - 5.39 ft) dependent on the load. See immersion rate below.

Engine

The boat is typically equipped with an inboard Westerbeke 4-107 diesel engine.

The fuel tank has a capacity of 151.0 liters (39 US gallons, 33 imperial gallons).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Cruisaire 36 is 1.67, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Cruisaire 36 is about 179 kg/cm, alternatively 1006 lbs/inch.
Meaning: if you load 179 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1006 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Cruisaire 36 is 35.8.

Comparing this ratio with similar sailboats show that it is more comfortable than 90% of all similar sailboat designs. This is a comfort value significantly above average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Cruisaire 36 is 3.38.

Compared with other similar sailboats it is slimmer than 69% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Cruisaire 36 is 30%.

This ballast ratio shows a righting moment that is higher than 8% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Cruisaire 36 is 343 which categorizes this boat among 'heavy cruisers'.

15% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Cruisaire 36 with ISO 8666 reference sail is 14.2, with a 135% genua the SA/D is 16.7.

The SA/D ratio indicates that it is faster than 18% of all similar sailboat designs in light wind.

Over- / underrigged

The Cruisaire 36 has more rig than 82% of all similar sailboats, which indicates that the boat is significantly overrigged.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 30m² (322 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail for ketch rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	28.2 m	(92.4 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	28.2 m	(92.4 feet)	12 mm	(1/2 inch)
Spinnaker halyard	28.2 m	(92.4 feet)	12 mm	(1/2 inch)
Jib sheet	10.8 m	(35.5 feet)	14 mm	(0.55 inch)
Genoa sheet	10.8 m	(35.5 feet)	14 mm	(0.55 inch)
Mainsheet	27.1 m	(88.7 feet)	14 mm	(0.55 inch)
Spinnaker sheet	23.8 m	(78.1 feet)	14 mm	(0.55 inch)
Cunningham	4.7 m	(15.5 feet)	12 mm	(1/2 inch)
Kickingstrap	9.4 m	(31.0 feet)	12 mm	(1/2 inch)
Clew-outhaul	9.4 m	(31.0 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Cruisaire 36 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.