Review of Baltic 73
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Baltic 73 or similar boat for sale
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The Baltic 73 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.
The boat can only enter major marinas as the draft is about 3.00 - 3.10 meter (9.84 - 10.14 ft) dependent on the load. See immersion rate below.
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Baltic 73 is 1.70, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 10.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Baltic 73 is about 681 kg/cm, alternatively 3817 lbs/inch.
Meaning: if you load 681 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 3817 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Baltic 73 is 4.05.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Baltic 73 with ISO 8666 reference sail is 21.9, with a 135% genua the SA/D is 25.8.
Sorry, we do not have sufficient statistical information available for this boat to provide a significant reliable analysis.
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 118m2 (1270 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
Dimensions of sail for masthead rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 64.7 m | (212.2 feet) | 14 mm | (0.55 inch) |
| Jib/genoa halyard | 64.7 m | (212.2 feet) | 14 mm | (0.55 inch) |
| Spinnaker halyard | 64.7 m | (212.2 feet) | 14 mm | (0.55 inch) |
| Jib sheet | 22.3 m | (73.2 feet) | 16 mm | (5/8 inch) |
| Genoa sheet | 22.3 m | (73.2 feet) | 16 mm | (5/8 inch) |
| Mainsheet | 55.8 m | (182.9 feet) | 16 mm | (5/8 inch) |
| Spinnaker sheet | 49.1 m | (161.0 feet) | 16 mm | (5/8 inch) |
| Cunningham | 9.1 m | (29.9 feet) | 14 mm | (0.55 inch) |
| Kickingstrap | 18.2 m | (59.7 feet) | 14 mm | (0.55 inch) |
| Clew-outhaul | 18.2 m | (59.7 feet) | 14 mm | (0.55 inch) |
This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.
We are always looking for new photos. If you can contribute with photos for Baltic 73 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.