Review of Atalanta 26

Basic specs.

The Atalanta 26 is a sailboat designed by the British maritime architect Uffa Fox in the mid fifties. A few hundred boats have been produced. The Atalanta 26 is built by the British yard Fairey Marine Ltd..

Here we would have liked to show you nice photos of the Atalanta 26.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Atalanta 26 or similar boat for sale

Hull

The hull is made of plywood.

Rig

The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

The boat can enter even shallow marinas as the draft is just about 0.46 - 0.56 meter (1.51 - 1.81 ft) dependent on the load. See immersion rate below.

Engine

The boat is typically equipped with a Coventry Victor gasoline engine.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Atalanta 26 is 1.94, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.7 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Atalanta 26 is about 119 kg/cm, alternatively 671 lbs/inch.
Meaning: if you load 119 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 671 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Atalanta 26 is 15.9.

Comparing this ratio with similar sailboats show that it is more comfortable than 27% of all similar sailboat designs. This comfort value is just below average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Atalanta 26 is 3.40.

Compared with other similar sailboats it is slimmer than 92% of all other designs. It seems that the designer has chosen a significantly more speedy hull design. This type of design is also referred to as 'needle'.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Atalanta 26 is 24%.

This ballast ratio shows a righting moment that is higher than 4% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Atalanta 26 is 114 which categorizes this boat among 'ultra light racers'.

92% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Atalanta 26 with ISO 8666 reference sail is 16.5, with a 135% genua the SA/D is 18.9.

The SA/D ratio indicates that it is faster than 58% of all similar sailboat designs in light wind.

Over- / underrigged

The Atalanta 26 has more rig than 100% of all similar sailboats, which indicates that the boat is significantly overrigged.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 23m² (247 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail for fractional rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	21.1 m	(69.2 feet)	8 mm	(5/16 inch)
Jib/genoa halyard	21.1 m	(69.2 feet)	8 mm	(5/16 inch)
Spinnaker halyard	21.1 m	(69.2 feet)	8 mm	(5/16 inch)
Jib sheet	8.0 m	(26.2 feet)	10 mm	(3/8 inch)
Genoa sheet	8.0 m	(26.2 feet)	10 mm	(3/8 inch)
Mainsheet	20.0 m	(65.5 feet)	10 mm	(3/8 inch)
Spinnaker sheet	17.6 m	(57.7 feet)	10 mm	(3/8 inch)
Cunningham	3.6 m	(11.7 feet)	8 mm	(5/16 inch)
Kickingstrap	7.1 m	(23.4 feet)	8 mm	(5/16 inch)
Clew-outhaul	7.1 m	(23.4 feet)	8 mm	(5/16 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Atalanta 26 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.