Udkik.dk

Review of Seawanhaka One Design


Basic specs.

sail specifications
The Seawanhaka One Design aka Seawanhaka OD is a sailboat designed by the American maritime architect bureau Sparkman & Stephens in the late thirties.

Here we would have liked to show you nice photos of the Seawanhaka One Design.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Seawanhaka One Design or similar boat for sale

Hull
The hull is made of wood.

Rig
The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

The Seawanhaka One Design is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can enter even shallow marinas as the draft is just about 1.37 - 1.47 meter (4.49 - 4.79 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Seawanhaka One Design is 1.38, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Seawanhaka One Design is about 86 kg/cm, alternatively 482 lbs/inch.
Meaning: if you load 86 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 482 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Seawanhaka One Design is 36.3.

Low High 97% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 97% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Seawanhaka One Design is 4.70.

Wide Slim 100% 0 50 100
Compared with other similar sailboats it is slimmer than 100% of all other designs. It seems that the designer has chosen a significantly more speedy hull design. This type of design is also referred to as 'needle'.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Seawanhaka One Design is 41%.

Low High 50% 0 50 100
This ballast ratio shows a righting moment that is higher than 50% of all similar sailboat designs. This righting moment (ability to resist heeling) is spot on average!


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Seawanhaka One Design is 337 which categorizes this boat among 'heavy cruisers'.

Heavy Light 15% 0 50 100
15% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Seawanhaka One Design with ISO 8666 reference sail is 16.6, with a 135% genua the SA/D is 18.6.

Low High 54% 0 50 100
The SA/D ratio indicates that it is faster than 54% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 93% 0 50 100
The Seawanhaka One Design has more rig than 93% of all similar sailboats, which indicates that the boat is significantly overrigged.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 16m2 (172 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for fractional rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 27.1 m(88.7 feet)10 mm(3/8 inch)
Jib/genoa halyard27.1 m(88.7 feet)10 mm(3/8 inch)
Spinnaker halyard27.1 m(88.7 feet)10 mm(3/8 inch)
Jib sheet 9.4 m(31.0 feet)12 mm(1/2 inch)
Genoa sheet9.4 m(31.0 feet)12 mm(1/2 inch)
Mainsheet 23.6 m(77.5 feet)12 mm(1/2 inch)
Spinnaker sheet20.8 m(68.2 feet)12 mm(1/2 inch)
Cunningham4.4 m(14.5 feet)10 mm(3/8 inch)
Kickingstrap8.8 m(29.0 feet)10 mm(3/8 inch)
Clew-outhaul8.8 m(29.0 feet)10 mm(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Seawanhaka One Design (S&S) it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References