Review of X-452

Basic specs.

The X-452 is a large sailboat designed by the maritime architect Niels Jeppesen in the late eighties. Only a few boats have been produced. The X-452 is built by the Danish yard X-Yachts A/S.

Here we would have liked to show you nice photos of the X-452.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a X-452 or similar boat for sale

Hull

The hull is made of hand laid fibreglass while the deck is made of fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season.

Interior

The interior is like most other boats made of teak.
The boat is equipped with 0 cabins, 10 berths, a galley and toilet facility.

Rig

The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The X-452 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can only enter major marinas as the draft is about 2.50 - 2.60 meter (8.20 - 8.50 ft) dependent on the load. See immersion rate below.

Engine

X-452 is typically equipped with an inboard Yanmar diesel engine at 55.0 hp (40 kW), which gives a max speed about 7.4 knots.

The transmission is a shaft drive. A shaft drive will in the long run require less maintenence than other types of drive e.g. a sail drive.

The fuel tank which is made of stainless steel has a capacity of 200.0 liters (52 US gallons, 43 imperial gallons).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for X-452 is 2.07, indicating that this boat would not be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for X-452 is about 306 kg/cm, alternatively 1718 lbs/inch.
Meaning: if you load 306 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1718 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for X-452 is 23.8.

Comparing this ratio with similar sailboats show that it is more comfortable than 18% of all similar sailboat designs. This is a comfort value significantly below average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for X-452 is 3.16.

Compared with other similar sailboats it is more spacy than 76% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for X-452 is 44%.

This ballast ratio shows a righting moment that is higher than 85% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly above average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for X-452 is 200 which categorizes this boat among 'light racers'.

66% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 55m² (592 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	13.4 m	(44.1 feet)	16 mm	(5/8 inch)
Genoa sheet	13.4 m	(44.1 feet)	16 mm	(5/8 inch)
Mainsheet	33.6 m	(110.3 feet)	16 mm	(5/8 inch)
Spinnaker sheet	29.6 m	(97.1 feet)	16 mm	(5/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for X-452 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.