Udkik.dk

Review of Swell 2


Swell 2
Swell 2 anno 1954. Billede af Swell 2 bygget 1954. Båden hedder Solo og ligger i Hvalpsund Marina.

Basic specs.

sail specifications
The Swell 2 is a sailboat designed by the Swedish maritime architect Knud Hielmberg Reimers. Only a few boats have been produced.

Looking for a new boat? Find a Swell 2 or similar boat for sale

Interior
The interior is like most other boats made of teak.
The boat is equipped with one cabin, 4 berths and a galley.

Keel
Keel
Keel of Swell 2 anno 1960. Dette skib er bygget af tømrermester Henry Nielsen, Åbyhøj i 1960. Han byggede det til sig selv og sin familie og var aktiv sejler i Århus til han døde omkring 1990. Den er bygget af mahogny på ask og eg med ruf og cockpit af teak.

The Swell 2 is equipped with a long keel. A long keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated.


Engine

The boat is typically equipped with an inboard Yanmar diesel engine at 9.0 hp (6 kW).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Swell 2 is 1.53, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Swell 2 is about 120 kg/cm, alternatively 673 lbs/inch.
Meaning: if you load 120 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 673 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Swell 2 is 3.39.

Wide Slim 92% 0 50 100
Compared with other similar sailboats it is slimmer than 92% of all other designs. It seems that the designer has chosen a significantly more speedy hull design. This type of design is also referred to as 'needle'.


Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 7.8 m(25.6 feet)10 mm(3/8 inch)
Genoa sheet 7.8 m(25.6 feet)10 mm(3/8 inch)
Mainsheet 19.5 m(64.0 feet)10 mm(3/8 inch)
Spinnaker sheet17.2 m(56.3 feet)10 mm(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Swell 2 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References