Review of Oyster 70
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Oyster 70 or similar boat for sale
The Oyster 70 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a long keel.
The boat can only enter major marinas as the draft is about 2.77 - 2.87 meter (9.09 - 9.39 ft) dependent on the load. See immersion rate below.
The boat is typically equipped with an inboard Perkins M225 Ti diesel engine at 225.0 hp (167 kW), which gives a max speed about 8.9 knots.
The fuel tank has a capacity of 1987.0 liters (524 US gallons, 437 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Oyster 70 is 1.53, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 10.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Oyster 70 is about 623 kg/cm, alternatively 3489 lbs/inch.
Meaning: if you load 623 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 3489 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Oyster 70 is 4.06.
SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 23.67
Sorry, we do not have sufficient statistical information available for this boat to provide a significant reliable analysis.
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 106m2 (1140 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 21.3 m | (70.0 feet) | 16 mm | (5/8 inch) |
| Genoa sheet | 21.3 m | (70.0 feet) | 16 mm | (5/8 inch) |
| Mainsheet | 53.4 m | (175.0 feet) | 16 mm | (5/8 inch) |
| Spinnaker sheet | 46.9 m | (154.0 feet) | 16 mm | (5/8 inch) |
This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.
We are always looking for new photos. If you can contribute with photos for Oyster 70 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.