Udkik.dk

Review of Oceanis Yacht 62


Basic specs.

sail specifications
The Oceanis Yacht 62 is a large sailboat designed by the French maritime architect bureau Berret-Racoupeau Yacht Design in the late 2010.

Here we would have liked to show you nice photos of the Oceanis Yacht 62.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Oceanis Yacht 62 or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Rig
The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

The boat can only enter major marinas as the draft is about 2.38 - 2.48 meter (7.81 - 8.11 ft) dependent on the load. See immersion rate below.


Engine

The boat is typically equipped with an inboard engine at 160.0 hp (119 kW), which gives a max speed about 9.5 knots.

The transmission is a shaft drive. A shaft drive will in the long run require less maintenence than other types of drive e.g. a sail drive.

The fuel tank has a capacity of 1000.0 liters (264 US gallons, 219 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Oceanis Yacht 62 is 1.81, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


EU classification

Oceanis Yacht 62 holds three CE certifications:

If less than 12 in on board the boat is by European Union certified as Class A. OCEAN:
Designed for extended voyages where conditions may exceed wind force 8 (Beaufort scale) and significant wave heights of 4 m and above but excluding abnormal conditions, and vessels largely self-sufficient.

If less than 14 in on board the boat is by European Union certified as Class B. OFFSHORE:
Designed for offshore voyages where conditions up to, and including, wind force 8 (Beaufort scale) and significant wave heights up to, and including, 4 m may be experienced.

If less than 16 in on board the boat is by European Union certified as Class C. INSHORE:
Designed for voyages in coastal waters, large bays, estuaries, lakes and rivers where conditions up to, and including, wind force 6 (Beaufort scale) and significant wave heights up to, and including, 2 m may be experienced.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 10.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Oceanis Yacht 62 is about 638 kg/cm, alternatively 3575 lbs/inch.
Meaning: if you load 638 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 3575 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Oceanis Yacht 62 is 3.40.

Slim Wide 82% 0 50 100
Compared with other similar sailboats it is more spacy than 82% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Oceanis Yacht 62 is 127 which categorizes this boat among 'ultra light racers'.

Heavy Light 79% 0 50 100
79% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 103m2 (1108 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 18.1 m(59.5 feet)16 mm(5/8 inch)
Genoa sheet18.1 m(59.5 feet)16 mm(5/8 inch)
Mainsheet 45.3 m(148.7 feet)16 mm(5/8 inch)
Spinnaker sheet39.9 m(130.9 feet)16 mm(5/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Oceanis Yacht 62 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References