Udkik.dk

Review of Mirage 338


Basic specs.

sail specifications
The Mirage 338 is a sailboat designed by the American maritime architect Bruce Kelley in the mid eighties. The Mirage 338 is built by the American yard Mirage Mfg..

Here we would have liked to show you nice photos of the Mirage 338.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Mirage 338 or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Keel

The Mirage 338 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a long keel.

The boat can only enter major marinas as the draft is about 1.83 - 1.93 meter (6.00 - 6.30 ft) dependent on the load. See immersion rate below.


Engine

The boat is typically equipped with an inboard Yanmar diesel engine.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Mirage 338 is 2.59, indicating that this boat would not be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Mirage 338 is about 191 kg/cm, alternatively 1071 lbs/inch.
Meaning: if you load 191 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1071 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Mirage 338 is 9.7.

Low High 1% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 1% of all similar sailboat designs. This is a comfort value significantly below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Mirage 338 is 3.16.

Slim Wide 54% 0 50 100
Compared with other similar sailboats it is more spacy than 54% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Mirage 338 is 54%.

Low High 96% 0 50 100
This ballast ratio shows a righting moment that is higher than 96% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly above average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Mirage 338 is 83 which categorizes this boat among 'ultra light racers'.

Heavy Light 98% 0 50 100
98% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 30.15


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 33m2 (355 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 10.3 m(33.7 feet)12 mm(1/2 inch)
Genoa sheet10.3 m(33.7 feet)12 mm(1/2 inch)
Mainsheet 25.6 m(84.2 feet)12 mm(1/2 inch)
Spinnaker sheet22.6 m(74.1 feet)12 mm(1/2 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Mirage 338 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References