Udkik.dk

Review of Møn 830


Møn 830
Møn 830.


Basic specs.

sail specifications
The Møn 830 is a motorsailer designed by the Swedish maritime architect Rolf Eliasson in the early eighties. The Møn 830 is built by the Danish yard Møn Boats A/S.

Looking for a new boat? Find a Møn 830 or similar boat for sale

Hull
The hull is made of hand laid fibreglass while the deck is made of fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.

Interior
Interior
Interior of Møn 830.
The interior is like most other boats made of teak.
The boat is equipped with 2 cabins, 4-5 berths, a galley and toilet facility.
Aft Cabin
Aft cabin of Møn 830.

Cockpit
Cockpit
Cockpit of Møn 830.
Rig
The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

The Møn 830 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can enter even shallow marinas as the draft is just about 1.25 - 1.35 meter (4.10 - 4.40 ft) dependent on the load. See immersion rate below.


Engine

Møn 830 is typically equipped with an inboard Yanmar diesel engine at 18.0 hp (13 kW), which gives a max speed about 5.4 knots.

The transmission is a saildrive.

The fuel tank which is made of stainless steel has a capacity of 120.0 liters (31 US gallons, 26 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Møn 830 is 2.00, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Møn 830 is about 125 kg/cm, alternatively 701 lbs/inch.
Meaning: if you load 125 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 701 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Møn 830 is 23.3.

Low High 66% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 66% of all similar sailboat designs. This comfort value is just above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Møn 830 is 2.84.

Slim Wide 76% 0 50 100
Compared with other similar sailboats it is more spacy than 76% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Møn 830 is 38%.

Low High 38% 0 50 100
This ballast ratio shows a righting moment that is higher than 38% of all similar sailboat designs. A righting moment (ability to resist heeling) just below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Møn 830 is 340 which categorizes this boat among 'heavy cruisers'.

Heavy Light 14% 0 50 100
14% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 20m2 (215 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 8.3 m(27.2 feet)10 mm(3/8 inch)
Genoa sheet8.3 m(27.2 feet)10 mm(3/8 inch)
Mainsheet 20.8 m(68.1 feet)10 mm(3/8 inch)
Spinnaker sheet18.3 m(59.9 feet)10 mm(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Møn 830 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References