The Hanseat has been built with more than one type of keel.
One option is a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
The boat can enter most marinas as the draft is just about 1.60 - 1.70 meter (5.25 - 5.55 ft) dependent on the load. See immersion rate below.
Hanseat is typically equipped with an inboard Volvo Penta MD2 diesel engine at 15.0 hp (11 kW), which gives a max speed about 4.8 knots.
The transmission is a shaft drive. A shaft drive will in the long run require less maintenence than other types of drive e.g. a sail drive.
The fuel tank has a capacity of 120.0 liters (31 US gallons, 26 imperial gallons).
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Hanseat is 1.82, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Hanseat is about 162 kg/cm, alternatively 907 lbs/inch.
Meaning: if you load 162 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 907 lbs cargo on the boat it will sink 1 inch.
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Hanseat is 24.8.
What is L/B (Length Beam Ratio)?
The l/b ratio for Hanseat is 3.46.
The ballast ratio for Hanseat is 35%.
What is Displacement Length Ratio?
The DL-ratio for Hanseat is 219 which categorizes this boat among 'light crusers & offshore racers'.
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 28m2 (301 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
Usage | Length | Diameter | ||
Jib sheet | 10.2 m | (33.5 feet) | 12 mm | (1/2 inch) |
Genoa sheet | 10.2 m | (33.5 feet) | 12 mm | (1/2 inch) |
Mainsheet | 25.5 m | (83.7 feet) | 12 mm | (1/2 inch) |
Spinnaker sheet | 22.4 m | (73.6 feet) | 12 mm | (1/2 inch) |
This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.
We are always looking for new photos. If you can contribute with photos for Hanseat it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.