Review of Skipper 17

Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

The boat is equipped with 2 berths.

The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

The Skipper 17 has been built with more than one type of keel.

One option is a centerboard keel. A centerboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

The boat can sail close to the beach as the draft is just 0.23 - 0.33 meter (0.75 - 1.05 ft) dependent of the load. See immersion rate below.

What is Capsize Screening Formula (CSF)?

The capsize screening value for Skipper 17 is 2.89, indicating that this boat would not be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 5.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Skipper 17 is about 63 kg/cm, alternatively 352 lbs/inch.
Meaning: if you load 63 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 352 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Skipper 17 is 5.6.

Comparing this ratio with similar sailboats show that it is more comfortable than 14% of all similar sailboat designs. This is a comfort value significantly below average.

What is L/B (Length Beam Ratio)?

The l/b ratio for Skipper 17 is 2.64.

Compared with other similar sailboats it is slimmer than 54% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

What is Displacement Length Ratio?

The DL-ratio for Skipper 17 is 80 which categorizes this boat among 'ultra light racers'.

88% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 30.29

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 11m² (118 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

We are always looking for new photos. If you can contribute with photos for Skipper 17 (Milne) it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.