Review of Swede 52

Basic specs.

The Swede 52 is a large sailboat designed by the Swedish maritime architect Knud Hielmberg Reimers together with Sven-Olof Ridder also from Sweden. The Swede 52 is built by the Swedish yard Allegro Båt AB.

Here we would have liked to show you nice photos of the Swede 52.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Swede 52 or similar boat for sale

Interior

The interior is like many other boats made of mahogany.
The boat is equipped with 7 berths.

Rig

The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

The Swede 52 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a long keel.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Swede 52 is 1.53, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Swede 52 is about 321 kg/cm, alternatively 1800 lbs/inch.
Meaning: if you load 321 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1800 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Swede 52 is 5.33.

Compared with other similar sailboats it is slimmer than 100% of all other designs. It seems that the designer has chosen a significantly more speedy hull design. This type of design is also referred to as 'needle'.

SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 23.63

Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	16.0 m	(52.5 feet)	16 mm	(5/8 inch)
Genoa sheet	16.0 m	(52.5 feet)	16 mm	(5/8 inch)
Mainsheet	40.0 m	(131.2 feet)	16 mm	(5/8 inch)
Spinnaker sheet	35.2 m	(115.5 feet)	16 mm	(5/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Swede 52 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.