Review of Southerly 115

Basic specs.

The Southerly 115 is a sailboat designed by the British maritime architect Richard Carter.

Here we would have liked to show you nice photos of the Southerly 115.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Southerly 115 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Interior

The boat is equipped with 8 berths.

Keel

The boat can enter even shallow marinas as the draft is just about 0.69 - 0.79 meter (2.26 - 2.56 ft) dependent on the load. See immersion rate below.

Engine

Southerly 115 is typically equipped with an inboard Yanmar diesel engine.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Southerly 115 is 1.95, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Southerly 115 is about 272 kg/cm, alternatively 1527 lbs/inch.
Meaning: if you load 272 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1527 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Southerly 115 is 3.11.

Compared with other similar sailboats it is more spacy than 66% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Southerly 115 is 50%.

This ballast ratio shows a righting moment that is higher than 93% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly above average.

SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 15.89

Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	11.2 m	(36.9 feet)	14 mm	(0.55 inch)
Genoa sheet	11.2 m	(36.9 feet)	14 mm	(0.55 inch)
Mainsheet	28.1 m	(92.3 feet)	14 mm	(0.55 inch)
Spinnaker sheet	24.8 m	(81.2 feet)	14 mm	(0.55 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Southerly 115 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.