Review of Salmo Salar

Basic specs.

The Salmo Salar is a sailboat designed by the British maritime architect bureau Laurent Giles & Partners Ltd. in the mid sixties. Less than 100 boats have been produced.

Here we would have liked to show you nice photos of the Salmo Salar.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Salmo Salar or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Rig

The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The Salmo Salar is equipped with a long keel. A long keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.

The boat can enter most marinas as the draft is just about 1.62 - 1.72 meter (5.31 - 5.61 ft) dependent on the load. See immersion rate below.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Salmo Salar is 1.58, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.5 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Salmo Salar is about 217 kg/cm, alternatively 1216 lbs/inch.
Meaning: if you load 217 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1216 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Salmo Salar is 42.6.

Comparing this ratio with similar sailboats show that it is more comfortable than 96% of all similar sailboat designs. This is a comfort value significantly above average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Salmo Salar is 3.47.

Compared with other similar sailboats it is slimmer than 69% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Salmo Salar is 34%.

This ballast ratio shows a righting moment that is higher than 24% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Salmo Salar is 349 which categorizes this boat among 'heavy cruisers'.

14% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Salmo Salar with ISO 8666 reference sail is 14.5, with a 135% genua the SA/D is 17.2.

The SA/D ratio indicates that it is faster than 21% of all similar sailboat designs in light wind.

Over- / underrigged

The Salmo Salar has more rig than 69% of all similar sailboats, which indicates that the boat is slightly overrigged.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 36m² (387 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail for masthead rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	33.3 m	(109.3 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	33.3 m	(109.3 feet)	12 mm	(1/2 inch)
Spinnaker halyard	33.3 m	(109.3 feet)	12 mm	(1/2 inch)
Jib sheet	11.9 m	(39.0 feet)	14 mm	(0.55 inch)
Genoa sheet	11.9 m	(39.0 feet)	14 mm	(0.55 inch)
Mainsheet	29.7 m	(97.5 feet)	14 mm	(0.55 inch)
Spinnaker sheet	26.2 m	(85.8 feet)	14 mm	(0.55 inch)
Cunningham	4.9 m	(16.0 feet)	12 mm	(1/2 inch)
Kickingstrap	9.8 m	(32.0 feet)	12 mm	(1/2 inch)
Clew-outhaul	9.8 m	(32.0 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Salmo Salar it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.