Review of Raider 35
Basic specs.
Looking for a new boat? Find a Raider 35 or similar boat for sale
The headroom is above average
The Raider 35 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.
The boat can enter most marinas as the draft is just about 1.52 - 1.62 meter (4.99 - 5.29 ft) dependent on the load. See immersion rate below.
Raider 35 is typically equipped with an inboard Yanmar 3GM30 diesel engine at 27.0 hp (20 kW), which gives a max speed about 5.0 knots.
The transmission is a shaft drive. A shaft drive will in the long run require less maintenence than other types of drive e.g. a sail drive.
The fuel tank which is made of stainless steel has a capacity of 57.0 liters (15 US gallons, 12 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Raider 35 is 1.73, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 6.6 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Raider 35 is about 159 kg/cm, alternatively 890 lbs/inch.
Meaning: if you load 159 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 890 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Raider 35 is 34.9.
What is L/B (Length Beam Ratio)?
The l/b ratio for Raider 35 is 3.33.
What is Displacement Length Ratio?
The DL-ratio for Raider 35 is 443 which categorizes this boat among 'heavy cruisers'.
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 26m2 (279 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 10.7 m | (34.9 feet) | 14 mm | (0.55 inch) |
| Genoa sheet | 10.7 m | (34.9 feet) | 14 mm | (0.55 inch) |
| Mainsheet | 26.6 m | (87.4 feet) | 14 mm | (0.55 inch) |
| Spinnaker sheet | 23.4 m | (76.9 feet) | 14 mm | (0.55 inch) |
This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.
We are always looking for new photos. If you can contribute with photos for Raider 35 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.