Udkik.dk

Review of Pacific Seacraft 34


Basic specs.

sail specifications
The Pacific Seacraft 34 is a sailboat designed by the British maritime architect William Ion Belton Crealock in the mid eighties.

Here we would have liked to show you nice photos of the Pacific Seacraft 34.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Pacific Seacraft 34 or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Interior
The headroom is above average

Keel

The Pacific Seacraft 34 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can enter most marinas as the draft is just about 1.50 - 1.60 meter (4.92 - 5.22 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Pacific Seacraft 34 is 1.68, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.9 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Pacific Seacraft 34 is about 163 kg/cm, alternatively 914 lbs/inch.
Meaning: if you load 163 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 914 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Pacific Seacraft 34 is 33.7.

Low High 88% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 88% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Pacific Seacraft 34 is 3.41.

Wide Slim 69% 0 50 100
Compared with other similar sailboats it is slimmer than 69% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Pacific Seacraft 34 is 36%.

Low High 27% 0 50 100
This ballast ratio shows a righting moment that is higher than 27% of all similar sailboat designs. A righting moment (ability to resist heeling) just below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Pacific Seacraft 34 is 334 which categorizes this boat among 'heavy cruisers'.

Heavy Light 15% 0 50 100
15% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Pacific Seacraft 34 with ISO 8666 reference sail is 15.1, with a 135% genua the SA/D is 17.9.

Low High 27% 0 50 100
The SA/D ratio indicates that it is faster than 27% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 76% 0 50 100
The Pacific Seacraft 34 has more rig than 76% of all similar sailboats, which indicates that the boat is significantly overrigged.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 27m2 (290 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 27.5 m(90.3 feet)10 mm(3/8 inch)
Jib/genoa halyard27.5 m(90.3 feet)10 mm(3/8 inch)
Spinnaker halyard27.5 m(90.3 feet)10 mm(3/8 inch)
Jib sheet 10.4 m(34.1 feet)12 mm(1/2 inch)
Genoa sheet10.4 m(34.1 feet)12 mm(1/2 inch)
Mainsheet 26.0 m(85.2 feet)12 mm(1/2 inch)
Spinnaker sheet22.9 m(75.0 feet)12 mm(1/2 inch)
Cunningham4.3 m(14.0 feet)10 mm(3/8 inch)
Kickingstrap8.5 m(28.0 feet)10 mm(3/8 inch)
Clew-outhaul8.5 m(28.0 feet)10 mm(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Pacific Seacraft 34 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References