Review of Mamba 36

Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.

The interior is like most other boats made of teak.
The boat is equipped with 4 cabins, 9 berths, a galley and toilet facility.

The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

The Mamba 36 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can enter most marinas as the draft is just about 1.78 - 1.88 meter (5.84 - 6.14 ft) dependent on the load. See immersion rate below.

Mamba 36 is typically equipped with an inboard Yanmar diesel engine at 27.0 hp (20 kW), which gives a max speed about 6.1 knots.

The transmission is a saildrive.

The fuel tank which is made of stainless steel has a capacity of 60.0 liters (15 US gallons, 13 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Mamba 36 is 1.83, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Mamba 36 is about 200 kg/cm, alternatively 1123 lbs/inch.
Meaning: if you load 200 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1123 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Mamba 36 is 25.4.

Comparing this ratio with similar sailboats show that it is more comfortable than 38% of all similar sailboat designs. This comfort value is just below average.

What is L/B (Length Beam Ratio)?

The l/b ratio for Mamba 36 is 3.43.

Compared with other similar sailboats it is slimmer than 76% of all other designs. It seems that the designer has chosen a significantly more speedy hull design.

What is a Ballast Ratio?

The ballast ratio for Mamba 36 is 40%.

This ballast ratio shows a righting moment that is higher than 54% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.

What is Displacement Length Ratio?

The DL-ratio for Mamba 36 is 194 which categorizes this boat among 'light racers'.

76% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Mamba 36 with ISO 8666 reference sail is 17.3, with a 135% genua the SA/D is 19.9.

The SA/D ratio indicates that it is faster than 58% of all similar sailboat designs in light wind.

The Mamba 36 has more rig than 69% of all similar sailboats, which indicates that the boat is slightly overrigged.

What is Relative Speed Performance?

The Relative Speed Performance for Mamba 36 is 66

The relative speed performance is 66 which means that a it is faster than 66% of all similar sailboat designs.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 35m² (376 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Dimensions of sail for fractional rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

We are always looking for new photos. If you can contribute with photos for Mamba 36 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.