Udkik.dk

Review of Hood 37


Basic specs.

sail specifications
The Hood 37 aka Blackwatch 37 or Little Harbor 37 is a sailboat designed by the American maritime architect Ted Hood in the mid sixties. Only a few boats have been produced. The Hood 37 is built by the American yard Little Harbor Yachts.

Here we would have liked to show you nice photos of the Hood 37.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Hood 37 or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Keel

The Hood 37 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can enter even shallow marinas as the draft is just about 1.37 - 1.47 meter (4.49 - 4.79 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Hood 37 is 1.72, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.8 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Hood 37 is about 166 kg/cm, alternatively 932 lbs/inch.
Meaning: if you load 166 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 932 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Hood 37 is 3.52.

Wide Slim 79% 0 50 100
Compared with other similar sailboats it is slimmer than 79% of all other designs. It seems that the designer has chosen a significantly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Hood 37 is 29%.

Low High 7% 0 50 100
This ballast ratio shows a righting moment that is higher than 7% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Hood 37 is 393 which categorizes this boat among 'heavy cruisers'.

Heavy Light 5% 0 50 100
5% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Hood 37 with ISO 8666 reference sail is 16.0, with a 135% genua the SA/D is 18.9.

Low High 38% 0 50 100
The SA/D ratio indicates that it is faster than 38% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 98% 0 50 100
The Hood 37 has more rig than 98% of all similar sailboats, which indicates that the boat is significantly overrigged.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 28m2 (301 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 30.5 m(100.0 feet)12 mm(1/2 inch)
Jib/genoa halyard30.5 m(100.0 feet)12 mm(1/2 inch)
Spinnaker halyard30.5 m(100.0 feet)12 mm(1/2 inch)
Jib sheet 11.3 m(37.0 feet)14 mm(0.55 inch)
Genoa sheet11.3 m(37.0 feet)14 mm(0.55 inch)
Mainsheet 28.2 m(92.5 feet)14 mm(0.55 inch)
Spinnaker sheet24.8 m(81.4 feet)14 mm(0.55 inch)
Cunningham4.6 m(15.0 feet)12 mm(1/2 inch)
Kickingstrap9.1 m(30.0 feet)12 mm(1/2 inch)
Clew-outhaul9.1 m(30.0 feet)12 mm(1/2 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Hood 37 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References