Review of High Tension 36

Basic specs.

The High Tension 36 is a sailboat designed by the Dutch maritime architect Jacobus de Ridder.

Here we would have liked to show you nice photos of the High Tension 36.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a High Tension 36 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Rig

The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The boat can only enter major marinas as the draft is about 2.02 - 2.12 meter (6.63 - 6.93 ft) dependent on the load. See immersion rate below.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for High Tension 36 is about 258 kg/cm, alternatively 1447 lbs/inch.
Meaning: if you load 258 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1447 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for High Tension 36 is 3.04.

Compared with other similar sailboats it is more spacy than 69% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

Maintenance

Rig

Dimensions of sail for masthead rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	33.5 m	(109.9 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	33.5 m	(109.9 feet)	12 mm	(1/2 inch)
Spinnaker halyard	33.5 m	(109.9 feet)	12 mm	(1/2 inch)
Jib sheet	10.8 m	(35.6 feet)	14 mm	(0.55 inch)
Genoa sheet	10.8 m	(35.6 feet)	14 mm	(0.55 inch)
Mainsheet	27.1 m	(88.9 feet)	14 mm	(0.55 inch)
Spinnaker sheet	23.8 m	(78.2 feet)	14 mm	(0.55 inch)
Cunningham	3.4 m	(11.0 feet)	12 mm	(1/2 inch)
Kickingstrap	6.7 m	(22.0 feet)	12 mm	(1/2 inch)
Clew-outhaul	6.7 m	(22.0 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for High Tension 36 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.