Review of Hanse 301

The hull is made of hand laid fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.

The interior is like many other boats made of mahogany.
The boat is equipped with 3 cabins, 6 berths, a galley and toilet facility.

The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

The Hanse 301 has been built with more than one type of keel.

One option is a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.But be aware that even though a Fin Keel keel is very good for speed racing, a fishing nets and the like in the water can easily make you into a troublesome situation.

The boat can enter most marinas as the draft is just about 1.68 - 1.78 meter (5.51 - 5.81 ft) dependent on the load. See immersion rate below.

Hanse 301 is typically equipped with an inboard Volvo Penta MD2010 diesel engine at 10.0 hp (7 kW).

The fuel tank has a capacity of 40.0 liters (10 US gallons, 8 imperial gallons).

Hanse 301 holds one CE certification:

The boat is by European Union certified as Class B. OFFSHORE:

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.8 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Hanse 301 is about 148 kg/cm, alternatively 829 lbs/inch.
Meaning: if you load 148 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 829 lbs cargo on the boat it will sink 1 inch.

What is L/B (Length Beam Ratio)?

The l/b ratio for Hanse 301 is 3.23.

Compared with other similar sailboats it is slimmer than 66% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

What is a Ballast Ratio?

The ballast ratio for Hanse 301 is 36%.

This ballast ratio shows a righting moment that is higher than 24% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 27m² (290 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

We are always looking for new photos. If you can contribute with photos for Hanse 301 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.