Udkik.dk

Review of Halman Horizon


Basic specs.

sail specifications
The Halman Horizon is a sailboat designed by the maritime architect Michael Volmer in the early eighties. The Halman Horizon is built by the Canadian yard Halman Manufacturing Co..

Here we would have liked to show you nice photos of the Halman Horizon.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Halman Horizon or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Rig
The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The Halman Horizon is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can enter even shallow marinas as the draft is just about 1.22 - 1.32 meter (4.00 - 4.30 ft) dependent on the load. See immersion rate below.


Engine

The boat is typically equipped with an inboard Volvo Penta diesel engine at 15.0 hp (11 kW), which gives a max speed about 5.2 knots.

The fuel tank has a capacity of 38.0 liters (10 US gallons, 8 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Halman Horizon is 2.02, indicating that this boat would not be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Halman Horizon is about 138 kg/cm, alternatively 775 lbs/inch.
Meaning: if you load 138 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 775 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Halman Horizon is 21.6.

Low High 58% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 58% of all similar sailboat designs. This comfort value is just above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Halman Horizon is 2.79.

Slim Wide 79% 0 50 100
Compared with other similar sailboats it is more spacy than 79% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Halman Horizon is 32%.

Low High 15% 0 50 100
This ballast ratio shows a righting moment that is higher than 15% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Halman Horizon is 256 which categorizes this boat among 'light crusers & offshore racers'.

Heavy Light 42% 0 50 100
42% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 22m2 (236 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 8.2 m(27.0 feet)10 mm(3/8 inch)
Genoa sheet8.2 m(27.0 feet)10 mm(3/8 inch)
Mainsheet 20.6 m(67.5 feet)10 mm(3/8 inch)
Spinnaker sheet18.1 m(59.4 feet)10 mm(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Halman Horizon it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References