Udkik.dk

Review of Fusion 62


Basic specs.

sail specifications
The Fusion 62 is a sailboat designed by the Danish maritime architect Erik Petersen in the late eighties. The Fusion 62 is built by the Danish yard P. Bjørn Olsens Bådeværft ApS.

Here we would have liked to show you nice photos of the Fusion 62.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Fusion 62 or similar boat for sale

Hull
Both the hull and the deck is made of hand laid fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.

Interior
The boat is equipped with 4 cabins, 10 berths, a galley and toilet facility.

Rig
The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

The Fusion 62 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can only enter major marinas as the draft is about 2.75 - 2.85 meter (9.02 - 9.32 ft) dependent on the load. See immersion rate below.


Engine

Fusion 62 is typically equipped with an inboard Volvo Penta 2003 Turbo 5 diesel engine at 43.0 hp (32 kW), which gives a max speed about 5.6 knots.

The transmission is a saildrive.

The fuel tank which is made of stainless steel has a capacity of 150.0 liters (39 US gallons, 32 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Fusion 62 is 1.64, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 9.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Fusion 62 is about 404 kg/cm, alternatively 2263 lbs/inch.
Meaning: if you load 404 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 2263 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Fusion 62 is 4.45.


Sorry, we do not have sufficient statistical information available for this boat to provide a significant reliable analysis.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 75m2 (807 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 18.5 m(60.7 feet)16 mm(5/8 inch)
Genoa sheet18.5 m(60.7 feet)16 mm(5/8 inch)
Mainsheet 46.3 m(151.8 feet)16 mm(5/8 inch)
Spinnaker sheet40.7 m(133.6 feet)16 mm(5/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Fusion 62 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References