Review of Finngulf 33

Both the hull and the deck is made of hand laid fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.

The interior is like most other boats made of teak.
The boat is equipped with 3 cabins, 6 berths, a galley and toilet facility.
Note: the boat has also been sold to be self-made/-interiored, which means that the quality of each boat may vary.

Finngulf 33 has more than one rig.

One option is a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

The Finngulf 33 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can enter most marinas as the draft is just about 1.75 - 1.85 meter (5.74 - 6.04 ft) dependent on the load. See immersion rate below.

The boat is typically equipped with an inboard Volvo Penta 2002 diesel engine at 18.0 hp (13 kW), which gives a max speed about 5.2 knots.

The transmission is a saildrive.

The fuel tank which is made of stainless steel has a capacity of 50.0 liters (13 US gallons, 10 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Finngulf 33 is 1.88, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Finngulf 33 is about 169 kg/cm, alternatively 947 lbs/inch.
Meaning: if you load 169 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 947 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Finngulf 33 is 24.3.

Comparing this ratio with similar sailboats show that it is more comfortable than 46% of all similar sailboat designs. This comfort value is just below average.

What is L/B (Length Beam Ratio)?

The l/b ratio for Finngulf 33 is 3.26.

Compared with other similar sailboats it is slimmer than 54% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

What is a Ballast Ratio?

The ballast ratio for Finngulf 33 is 48%.

This ballast ratio shows a righting moment that is higher than 82% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly above average.

What is Displacement Length Ratio?

The DL-ratio for Finngulf 33 is 227 which categorizes this boat among 'light crusers & offshore racers'.

58% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Finngulf 33 with ISO 8666 reference sail is 20.1, with a 135% genua the SA/D is 23.1.

The SA/D ratio indicates that it is faster than 90% of all similar sailboat designs in light wind.

The Finngulf 33 has more rig than 62% of all similar sailboats, which indicates that the boat is slightly overrigged.

What is Relative Speed Performance?

The Relative Speed Performance for Finngulf 33 is 88

The relative speed performance is 88 which means that a it is faster than 88% of all similar sailboat designs.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 30m² (322 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Dimensions of sail for fractional rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

We are always looking for new photos. If you can contribute with photos for Finngulf 33 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.