Review of Conway 36

Basic specs.

The Conway 36 is a sailboat designed by the British maritime architect Jack Laurent Giles in the mid seventies. The Conway 36 is built by the British yard Westerly Marine Ltd..

Here we would have liked to show you nice photos of the Conway 36.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Conway 36 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Rig

The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The Conway 36 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a long keel.

The boat can only enter major marinas as the draft is about 1.83 - 1.93 meter (6.00 - 6.30 ft) dependent on the load. See immersion rate below.

Engine

The boat is typically equipped with an inboard Mercedes-Benz diesel engine.

The fuel tank has a capacity of 159.0 liters (42 US gallons, 34 imperial gallons).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Conway 36 is 1.77, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Conway 36 is about 210 kg/cm, alternatively 1176 lbs/inch.
Meaning: if you load 210 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1176 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Conway 36 is 31.2.

Comparing this ratio with similar sailboats show that it is more comfortable than 73% of all similar sailboat designs. This comfort value is just above average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Conway 36 is 3.21.

Compared with other similar sailboats it is more spacy than 50% of all other designs. It seems that the designer has chosen an average hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Conway 36 is 44%.

This ballast ratio shows a righting moment that is higher than 73% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Conway 36 is 260 which categorizes this boat among 'light crusers & offshore racers'.

50% of all similar sailboat designs are categorized as heavier. This boat has a precise average ratio between displacement and length!

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Conway 36 with ISO 8666 reference sail is 12.7, with a 135% genua the SA/D is 15.4.

The SA/D ratio indicates that it is faster than 8% of all similar sailboat designs in light wind.

Over- / underrigged

The Conway 36 has more rig than 18% of all similar sailboats, which indicates that the boat is significantly underrigged.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 36m² (387 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail for masthead rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	28.0 m	(91.8 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	28.0 m	(91.8 feet)	12 mm	(1/2 inch)
Spinnaker halyard	28.0 m	(91.8 feet)	12 mm	(1/2 inch)
Jib sheet	10.9 m	(35.8 feet)	14 mm	(0.55 inch)
Genoa sheet	10.9 m	(35.8 feet)	14 mm	(0.55 inch)
Mainsheet	27.2 m	(89.4 feet)	14 mm	(0.55 inch)
Spinnaker sheet	24.0 m	(78.7 feet)	14 mm	(0.55 inch)
Cunningham	3.5 m	(11.5 feet)	12 mm	(1/2 inch)
Kickingstrap	7.0 m	(23.0 feet)	12 mm	(1/2 inch)
Clew-outhaul	7.0 m	(23.0 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Conway 36 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.