Udkik.dk

Review of Capo 26


Capo 26
Capo 26. Amorous, Capo 26 hull #10, owner Chuck Holland

Basic specs.

sail specifications
The Capo 26 is a sailboat designed by the American maritime architect Carl Schumacher in the early eighties. The Capo 26 is built by the British yard Westerly Marine.

Looking for a new boat? Find a Capo 26 or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Rig
The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The Capo 26 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a long keel.

The boat can enter even shallow marinas as the draft is just about 1.40 - 1.50 meter (4.59 - 4.89 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Capo 26 is 2.28, indicating that this boat would not be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Capo 26 is about 126 kg/cm, alternatively 709 lbs/inch.
Meaning: if you load 126 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 709 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Capo 26 is 14.7.

Low High 21% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 21% of all similar sailboat designs. This is a comfort value significantly below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Capo 26 is 2.81.

Slim Wide 76% 0 50 100
Compared with other similar sailboats it is more spacy than 76% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Capo 26 is 44%.

Low High 69% 0 50 100
This ballast ratio shows a righting moment that is higher than 69% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Capo 26 is 179 which categorizes this boat among 'light racers'.

Heavy Light 73% 0 50 100
73% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Capo 26 with ISO 8666 reference sail is 20.0, with a 135% genua the SA/D is 23.9.

Low High 88% 0 50 100
The SA/D ratio indicates that it is faster than 88% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 92% 0 50 100
The Capo 26 has more rig than 92% of all similar sailboats, which indicates that the boat is significantly overrigged.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 21m2 (226 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for masthead rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 23.7 m(77.7 feet)8 mm(5/16 inch)
Jib/genoa halyard23.7 m(77.7 feet)8 mm(5/16 inch)
Spinnaker halyard23.7 m(77.7 feet)8 mm(5/16 inch)
Jib sheet 7.9 m(26.0 feet)10 mm(3/8 inch)
Genoa sheet7.9 m(26.0 feet)10 mm(3/8 inch)
Mainsheet 19.8 m(65.0 feet)10 mm(3/8 inch)
Spinnaker sheet17.4 m(57.2 feet)10 mm(3/8 inch)
Cunningham3.0 m(10.0 feet)8 mm(5/16 inch)
Kickingstrap6.1 m(20.0 feet)8 mm(5/16 inch)
Clew-outhaul6.1 m(20.0 feet)8 mm(5/16 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Capo 26 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References