Udkik.dk

Review of Brewer 44


Basic specs.

sail specifications
The Brewer 44 is a large sailboat designed by the Canadian maritime architect Edward S. Brewer in the mid eighties.

Here we would have liked to show you nice photos of the Brewer 44.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Brewer 44 or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Keel

The Brewer 44 is equipped with a centerboard keel. A centerboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

The boat can enter even shallow marinas as the draft is just about 1.37 - 1.47 meter (4.49 - 4.79 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Brewer 44 is 1.76, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.9 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Brewer 44 is about 293 kg/cm, alternatively 1645 lbs/inch.
Meaning: if you load 293 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1645 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Brewer 44 is 36.9.

Low High 73% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 73% of all similar sailboat designs. This comfort value is just above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Brewer 44 is 3.26.

Slim Wide 62% 0 50 100
Compared with other similar sailboats it is more spacy than 62% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Brewer 44 is 41%.

Low High 69% 0 50 100
This ballast ratio shows a righting moment that is higher than 69% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Brewer 44 is 301 which categorizes this boat among 'medium weight cruisers'.

Heavy Light 21% 0 50 100
21% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Brewer 44 with ISO 8666 reference sail is 16.2, with a 135% genua the SA/D is 19.1.

Low High 21% 0 50 100
The SA/D ratio indicates that it is faster than 21% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 10% 0 50 100
The Brewer 44 has more rig than 10% of all similar sailboats, which indicates that the boat is significantly underrigged.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 55m2 (592 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 37.5 m(123.0 feet)14 mm(0.55 inch)
Jib/genoa halyard37.5 m(123.0 feet)14 mm(0.55 inch)
Spinnaker halyard37.5 m(123.0 feet)14 mm(0.55 inch)
Jib sheet 13.4 m(44.0 feet)16 mm(5/8 inch)
Genoa sheet13.4 m(44.0 feet)16 mm(5/8 inch)
Mainsheet 33.5 m(110.0 feet)16 mm(5/8 inch)
Spinnaker sheet29.5 m(96.8 feet)16 mm(5/8 inch)
Cunningham5.9 m(19.4 feet)14 mm(0.55 inch)
Kickingstrap11.8 m(38.8 feet)14 mm(0.55 inch)
Clew-outhaul11.8 m(38.8 feet)14 mm(0.55 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Brewer 44 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References