Review of Baltic 35

Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.

The interior is like most other boats made of teak.
The boat is equipped with 3 cabins, 6 berths, a galley and toilet facility.

The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

The Baltic 35 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can only enter major marinas as the draft is about 1.85 - 1.95 meter (6.07 - 6.37 ft) dependent on the load. See immersion rate below.

Baltic 35 is typically equipped with an inboard Yanmar 2GM20F diesel engine at 18.0 hp (13 kW), which gives a max speed about 5.4 knots.

The transmission is a shaft drive. A shaft drive will in the long run require less maintenence than other types of drive e.g. a sail drive.

The fuel tank which is made of stainless steel has a capacity of 100.0 liters (26 US gallons, 21 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Baltic 35 is 2.14, indicating that this boat would not be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Baltic 35 is about 205 kg/cm, alternatively 1148 lbs/inch.
Meaning: if you load 205 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1148 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Baltic 35 is 19.2.

Comparing this ratio with similar sailboats show that it is more comfortable than 14% of all similar sailboat designs. This is a comfort value significantly below average.

What is L/B (Length Beam Ratio)?

The l/b ratio for Baltic 35 is 3.04.

Compared with other similar sailboats it is more spacy than 69% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

What is a Ballast Ratio?

The ballast ratio for Baltic 35 is 42%.

This ballast ratio shows a righting moment that is higher than 62% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.

What is Displacement Length Ratio?

The DL-ratio for Baltic 35 is 186 which categorizes this boat among 'light racers'.

79% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 35m² (376 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

We are always looking for new photos. If you can contribute with photos for Baltic 35 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.