Review of Caprice

Caprice anno 1974.

Basic specs.

The Caprice aka Caprice 30 is a sailboat designed by the maritime architect Axel Eisenhardt in the late sixties.

Looking for a new boat? Find a Caprice or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.

Interior

The boat is equipped with 4 berths and a galley.

Rig

Rig of Caprice anno 1972.

The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

Keel of Caprice anno 1974.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 5.9 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Caprice is about 81 kg/cm, alternatively 456 lbs/inch.
Meaning: if you load 81 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 456 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Caprice is 4.42.

Compared with other similar sailboats it is slimmer than 100% of all other designs. It seems that the designer has chosen a significantly more speedy hull design. This type of design is also referred to as 'needle'.

RSP (Relative Speed Performance)

What is Relative Speed Performance?

The Relative Speed Performance for Caprice is 38

The relative speed performance is 38 which means that a it is faster than 38% of all similar sailboat designs.

Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	9.0 m	(29.4 feet)	10 mm	(3/8 inch)
Genoa sheet	9.0 m	(29.4 feet)	10 mm	(3/8 inch)
Mainsheet	22.4 m	(73.6 feet)	10 mm	(3/8 inch)
Spinnaker sheet	19.7 m	(64.7 feet)	10 mm	(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Caprice (Eisenhardt) it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.